Hot Press Injection Pressing Plate Vulcanizing Machine Dual Heads

Power Conservation Dual Heads Hot Press Machine

The injection-pressing plate vulcanizing machine is used as a conveyor belt connector. During and after use, it should be protected and maintained in the same way as other things to extend the service life.
Attentions During The Protection And Maintenance Of Injection-Pressing Plate Vulcanizer:

1. The storage environment of the injection-pressing plate vulcanizing machine should be dry and well-ventilated to prevent the electrical circuit from being wet due to humidity;
2. Do not use the injection-pressing plate vulcanizing machine outdoors on rainy days to prevent water from the electric control box and heating plate;
3. If the working environment is humid and watery, when disassembling and transferring the injection-pressing plate vulcanizing machine, you should use items to raise it on the ground, and do not let the injection-pressing plate vulcanizing machine directly touch the water.
4. If water enters the heating plate properly, contact the manufacturer for repair first. If emergency repairs are required, you can open the cover of the heating plate, pour out the water first, and then set the electric control box to manual operation, heat it to 100°C, maintain a constant temperature for half an hour, and dry the line. Glue the belt in the manual state. At the same time, the manufacturer should be contacted in time to replace all the lines.
5. If the injection-pressing plate vulcanizer does not need to be used for a long time, the heating plate should be heated every half a month, and the temperature should be maintained for about half an hour.
6. After each use, the water in the water pressure plate should be kept clean, especially in winter. If the water cannot be kept clean, it will often lead to premature aging of the water pressure plate rubber and decrease the service life of the water pressure plate; the correct way of water discharge Yes, after the vulcanization and heat preservation are completed, the injection-compression plate vulcanizer is not disassembled. If the water is discharged after the machine is disassembled, the water in the water pressure plate may not be completely discharged.

Matters Needing Attention When Using Injection-Pressing Plate Vulcanizer:

1. For machines operated by solenoid valves, the operator must not tamper with the solenoid valves. When faults occur, it is necessary to find electrical and external personnel for maintenance. Before maintenance, it is necessary to block the power supply.
2. When starting the pull-out machine and the splint, first ring the bell and call for contact. If you don't get a reply, you can't start it. During operation, do not reach into the splint. Personnel who are not on this machine are not allowed to arbitrarily put on the splint or press the button. When the front and rear pull-out machine starts, the operator is 0.5 meters away from the roller.
3. When changing horns, be stable and accurate, and don't use too much force. Before changing horns in series, it is necessary to tell the people around the pot to get out of the way to prevent hurting people.
4. When picking up the top iron, it is necessary to wait until the middle hot plate and the upper hot plate are completely separated. After picking up all the top irons, put down the iron plates.
5. When lowering the pot and turning over the iron plate, it is forbidden to reach into the pot. When loading the pot, keep your hands within 10 cm between the upper and lower heating plates. It is forbidden to reach between the heating plates. If problems are found, the machine should be stopped for handling.
6. When holding the iron rod used for winding the product, hold it firmly and firmly. When walking, pay attention to underground obstacles, and take care of them to prevent injuries to limbs.
7. When starting the packaging machine, check back and forth to prevent injury. When leading the lead, it is necessary for two people to be 0.5 meters away from the roller. Cooperate well with each other, and then start driving.
8. When hoisting the product, first check whether the wire rope is damaged. When hoisting, it is necessary to announce the signal first. It is forbidden to stand under the transported goods. When hoisting semi-products, the wire rope must be hung in the groove of the take-up roller.
9. When hoisting semi-finished products on the guide frame, it is necessary for two people to operate in the direction of the notch on both sides of the guide frame. After placing it, block the card sleeve.
10. When using an electric drill or a pot cleaner, it is necessary to check whether it is safe and reliable, whether the electrical circuit is damaged, and if there is a problem, it is necessary to repair it before using it.
11. When transferring the scouring machine, several people should cooperate with each other and hold it firmly. When changing the sandpaper, it is necessary to tighten the screws, and the electrical switches must be performed by special personnel to avoid accidents.
12. The vulcanized nylon conveyor belt is forbidden to go back and forth under the cold watch

Plate Vulcanizing Machine Parameters:

 
Reference Machine Images: