Payment & Shipping Terms:
|Clamp Force:||100 Ton||Upper Platen Size:||380*400mm|
|Lower Platen Size:||400*460mm||Plunger Stroke:||200mm|
|Heating Plates Distance:||200mm||Machine's Dimensions:||2500*2150*2080mm|
rubber compression machine,
rubber compression moulding machine
100 Ton Residential Magic Saksak Reusable Silicone Gloves Vacuum Molding Machine
Machine Operation Instructions:
The vulcanizer should use the handling equipment as much as possible when transporting. If it is transported with steel pipe, its diameter should not exceed 60mm. The machine should not be tilted excessively to prevent accidents and damage the parts and surface paint.
The vulcanizer should be placed on a stable surface and the horizontal and horizontal levels should be corrected with a level meter.
Add pure 68# anti-wear hydraulic oil to the fuel tank. The oil level should be above the top line of the oil level gauge. After the trial run, you need to make up.
Remove the sundries from the hot plate and adjust the red needle to the corresponding pressure according to the size of the mold. The maximum is not more than 20Mpa. The green needle is the automatic pressure, which is generally about 10% lower than the red needle. Fill the skateboard and roller with high temperature grease.
Turn on the three-phase four-wire power supply and rotate the “automatic” and “manual” to the automatic position. Press the "Reset" button, then press the "Stop" button to check that the end of the fully automatic vulcanizer motor shaft must be clockwise. The electric control box must be connected to the neutral line, and the host should be grounded with a 4 mm square wire.
Brief Introduction of Vacuum Compression Machine:
The hood vacuum vulcanizer is a new type of vacuum pressure forming equipment, which is mainly suitable for hot press forming of rubber products with complicated shape, easy gas lag and three-layer stencil production. Such as: automotive, household appliances, electronic parts, medical equipment, sports equipment and other industries supporting the production of rubber parts and butyl rubber medical corks with shallow cavities and high molding requirements. Product features: unit pressure up to 6.4MPa, product waste edge thin, easy to remove, high quality finished product; using PLC programmable controller and 7-inch touch screen, fully automatic control of the work process users can quickly modify and lock the process according to the needs of their own processes Parameters, to ensure product quality; with fast mold clamping, mold opening function, high production efficiency; with automatic access mode mechanism, easy to take parts, reduce labor intensity; with double-layer outer die (upper mold support flip and middle mold support Function), it is not easy to damage the mold and improve the service life of the mold; it is especially suitable for the complex shape of the two; the electric heating uses an electronic temperature controller to control and display the temperature of the hot plate. The temperature is accurate and the temperature is intuitive. The individual blocks can be controlled individually. Hot plate temperature; hydraulic adopts high and low pressure double pump oil supply mode, high efficiency, energy saving, safe and reliable; with automatic deflation function, the number of deflation can be adjusted arbitrarily, venting mold opening distance can be controlled by venting limit; with automatic pressure compensation function The raw material flow can be automatically replenished during the pressing process.
Main Technical Parameters:
|Upper Platen Size||mm||380*400|
|Lower Platen Size||mm||400*460|
|Distance of Thermo-plate||mm||200|
|Distance of Tie bar||mm||490*230|
|Die sinking type||2RT-3RT-4RT-Track|
|Max Operating Pressure||Mpa||20|
|Electric Heating Power||Kw||7.2*2|
|Vacuum Pump Power||Kw||3|
Other Vacuum Compression Machine Parameters:
|Upper Platen Size||mm||510*510||600*600||680*680||800*800||950*950|
|Lower Platen Size||mm||550*560||650*600||700*800||850*850||1000*1000|
Distance of Thermo
|Distance of Tie bar||mm||640*310||745*310||785*380||940*450||1105*475|
|Die sinking type||2RT-3RT-4RT-Track|
Contact Person: info